Eton VECTOR 250 - SERVICE Page 63 Service Manual Download

Page: 63 / 154

Installation

Caution

Pull out driven face to avoid it closing.

Cannot oppress friction plate comp in order
to avoid creates the distortion or the
damage.

Install drive belt onto driven pulley.

Install the driven pulley that has installed the belt

onto drive shaft.

On the drive belt another end to the movable drive

face.

Install the clutch outer and bearing stay collar.

Hold the clutch outer whit universal holder, and

then tighten nut to specified torque value.

Torque value: 5.0~6.0kgf-m

Install the drive face, washer and drive face nut.

Hold drive face with universal holder, and then

tighten nut to specified torque value.

Torque value: 8.5~10.5kgf-m

Driven face

Universal holder

Bearing stay collar

Summary of Contents for VECTOR 250 - SERVICE



























































































































































Search results

Summary of Contents for VECTOR 250 - SERVICE

Reviews:

Related manuals for VECTOR 250 - SERVICE

Brands by name

Popular brands

Eton VECTOR 250 - SERVICE, Service Manual

Search results

Summary of Contents for VECTOR 250 - SERVICE

Reviews:

Related manuals for VECTOR 250 - SERVICE

Brands by name

Popular brands