Eton VECTOR 250 - SERVICE Page 38 Service Manual Download

Page: 38 / 154

Remove left crankcase cover, and turn the
Turn the drive face, and align the timing mark on
the sprocket with that of cylinder head, piston is at
TDC position.
Remove cam sprocket bolts and then remove the
sprocket by prying chain out.

Remove cam shaft setting plate (1 bolt).

Remove rocker arm shafts and rocker arms.

Special Service Tool:
Rocker arm and cam shaft puller

Remove cam shafts.

Special Service Tool:
Rocker arm and cam shaft puller

Cam shafts

Cam shaft setting plate

2 bolts

Timing mark

Rocker arm

shaft and cam
shaft puller

Rocker arm shafts

Rocker arm shaft and

cam shaft puller

Summary of Contents for VECTOR 250 - SERVICE



























































































































































Search results

Summary of Contents for VECTOR 250 - SERVICE

Reviews:

Related manuals for VECTOR 250 - SERVICE

Brands by name

Popular brands

Eton VECTOR 250 - SERVICE, Service Manual

Search results

Summary of Contents for VECTOR 250 - SERVICE

Reviews:

Related manuals for VECTOR 250 - SERVICE

Brands by name

Popular brands