manualshive.com logo in svg

Eton VECTOR 250 - SERVICE, Service Manual, Page: 66 / 154

Share
Download
Eton VECTOR 250 - SERVICE Service Manual Download Page 66

66 

 

With 4~5g grease spreads wipes drives in the 

movable drive face axis hole. 

Install drive face boss. 

 Caution 

The movable drive face surface has to be free of 
grease.    Clean it with cleaning solvent. 

 

 

 

 

Install movable drive face comp. onto crankshaft. 

 

 

 

 

 

 

 

 

 

 

Driven pulley installation 

Press drive belt into pulley groove, and then pull 

the belt onto drive shaft. 

 

 

 

 

 

 

 

 

Install drive face, washer and nut. 

 Caution 

Make sure that two sides of pulley surfaces have 
to be free of grease.    Clean it with cleaning 
solvent. 

Hold drives face with universal holder. 

Tighten nut to specified torque. 

Torque value: 8.5~10.5kgf-m 

Install left crankcase cover. 

 

 

 

 

 

 

 

Drive face boss

Crank shaft 

Drive face boss

Movable drive face

Drive belt 

Press down 

Summary of Contents for VECTOR 250 - SERVICE



























































































































































Reviews:

No comments