Equinox Systems ISPnano I Series Page 64 User Manual Download

Page: 64 / 135

Distributor of Equinox Technologies: Excellent Integrated System Limited

Datasheet of ISPNANO S3 KIT - ISP PORTABLE PROGRAMMER
Contact us: [email protected] Website: www.integrated-circuit.com

ISPnano Series Programmer - User Manual – V1.11 – 12

May 2011

3. Connect the supplied USB cable between the USB Port on the rear of the programmer and a spare

USB port either on the PC or a USB Powered Hub.

The PC should display a message “

Found new hardware…..”

•

Follow the on-screen instructions to install the USB Driver.

•

Please refer to Application Note AN126 for further instructions.

3.4.3 Selecting the USB – Virtual COM Port (VCP) in EQTools

•

Make sure the USB cable is connected between the programmer and PC

•

Power up the programmer

•

In EQTools, select

<Programmer> <Communications and scripting settings>

•

Select the COM port which corresponds to the VCP which the programmer is connected to.

•

Click

<Test>

to test if the PC can communicate to the programmer via USB

Please refer to Application Note AN126 for further instructions on setting up and testing the USB

‘Virtual COM Port’

64 / 135

Summary of Contents for ISPnano I Series








































































































































Search results

Summary of Contents for ISPnano I Series

Reviews:

Related manuals for ISPnano I Series

Brands by name

Popular brands

Equinox Systems ISPnano I Series, User Manual

Search results

Summary of Contents for ISPnano I Series

Reviews:

Related manuals for ISPnano I Series

Brands by name

Popular brands