Equinox Systems ISPnano I Series User Manual Download Page 106

Page: 106 / 135

Distributor of Equinox Technologies: Excellent Integrated System Limited

Datasheet of ISPNANO S3 KIT - ISP PORTABLE PROGRAMMER
Contact us: [email protected] Website: www.integrated-circuit.com

ISPnano Series Programmer - User Manual – V1.11 – 12

May 2011

1.5 Atmel AT91SAM7 microcontroller - JTAG connections

The schematic below shows the connections required to In-System Program (ISP) an Atmel
AT91SAM7 ARM7 microcontroller via the JTAG Interface.

The table below details the connections for programming Atmel AVR microcontrollers via the JTAG
Interface.

Pin
No

Programmer
Pin name

Programmer
Input /
Output

Connect to
pin on
Target System

Notes

1 + 2

TARGET_VCC

Target VCC

3 + 4

TARGET_EXT_VCC P

See notes.

Target External VCC

5 + 6

PROG_GND

Signal GROUND
(0V)

Signal Ground Connection

Programmer I/O5

I/O

Spare I/O

Programmer I/O4

I/O

JTAG – TMS

Programmer I/O3

I/O

JTAG - TCK

Programmer I/O2

I/O

JTAG - TDO

Programmer I/O1

I/O

JTAG - TDI

PROG_RESET

RESET

Target RESET control pin

Please refer to Application Note AN122 for detailed instructions of how to program an Atmel

AT91SAM7 microcontroller.

106 / 135

Summary of Contents for ISPnano I Series








































































































































Search results

Summary of Contents for ISPnano I Series

Reviews:

Equinox Systems ISPnano I Series, User Manual, Page: 106 / 135

Search results

Summary of Contents for ISPnano I Series

Reviews: