Equinox Systems ISPnano I Series User Manual Download Page 107

Page: 107 / 135

Distributor of Equinox Technologies: Excellent Integrated System Limited

Datasheet of ISPNANO S3 KIT - ISP PORTABLE PROGRAMMER
Contact us: [email protected] Website: www.integrated-circuit.com

ISPnano Series Programmer - User Manual – V1.11 – 12

May 2011

1.6 Serial EEPROM – I2C connections

The schematic below shows the connections required to In-System Program (ISP) a single 24xxx

Serial EEPROM Memory device using the ISPnano programmer.

The table below details the connections for programming an I2C Serial EEPROM device via the I2C
Interface.

Pin
No

Programmer
Pin name

Programmer
Input /
Output

Connect to
pin on
Target System

Notes

1 + 2

TARGET_VCC

Target VCC

This pin should be connected to
the Target System Vcc.

5 + 6

PROG_GND

Signal GROUND
(0V)

Signal Ground Connection (1)

0V to which the programmer
JTAG, SPI, I2C signal lines are
referenced to.

I2C_SCL

I/O

I2C SCL

I2C SCL clock signal

This is the I2C SCL clock signal.

I2C_SDA

I/O

I2C SDA

I2C SDA data signal

This is the I2C SDA data signal.

Please refer to Application Note AN118 for detailed instructions of how to program Serial EEPROM

memory device via the I2C interface.

107 / 135

Summary of Contents for ISPnano I Series








































































































































Search results

Summary of Contents for ISPnano I Series

Reviews:

Equinox Systems ISPnano I Series, User Manual, Page: 107 / 135

Search results

Summary of Contents for ISPnano I Series

Reviews: