Epson TM-C3500 Series Technical Reference Manual Download Page 64

Page: 64 / 240

Replacing Maintenance Box

he s

eps below

o replace

he ma

int

ce box.

Turn the printer OFF.

Open the maintenance box cover towards you.

Pull out the used maintenance box towards you.



Do not dismantle the Maintenance box.



Do not touch the IC chip on the cartridge.



Keep out of reach of children, and do not drink.



Do not reuse a maintenance box which was removed and detached for a long period.



When using the printer for the first time, the replacement interval for the maintenance
box is shorter than usual as ink charging consumes the ink.

Summary of Contents for TM-C3500 Series

















































































































































































































































Search results

Summary of Contents for TM-C3500 Series

Reviews:

Related manuals for TM-C3500 Series

Brands by name

Popular brands

Epson TM-C3500 Series, Technical Reference Manual

Search results

Summary of Contents for TM-C3500 Series

Reviews:

Related manuals for TM-C3500 Series

Brands by name

Popular brands