Epson TM-C3500 Series Technical Reference Manual Download

Page: 202 / 240

202

Temperatures/

humidity

(See

"Environmental

Conditions" on

page 238

for

details.)

Printing

10 to 35



C, 20 to 80%RH (no condensation)

Storage

When packed (ink not loaded): -20 to 60



C, 5 to 85%RH (no

condensation)

-20



C or 60



C: up to 120 hours

Ink loaded: -20 to 40



-20



C: up to 120 hours

0 to 30



C: up to 6 months



C: up to a month

Overall dimensions (H × W × D)

310 × 283 × 261 mm (excluding protrusions)

Weight (mass)

Approximately 12 kg {26.45 lb}



(Not including the ink cartridge, maintenance box, AC adapter,

and roll paper).

Summary of Contents for TM-C3500 Series

















































































































































































































































Search results

Summary of Contents for TM-C3500 Series

Reviews:

Related manuals for TM-C3500 Series

Brands by name

Popular brands

Epson TM-C3500 Series, Technical Reference Manual

Search results

Summary of Contents for TM-C3500 Series

Reviews:

Related manuals for TM-C3500 Series

Brands by name

Popular brands