Epson TM-C3500 Series Technical Reference Manual Download Page 48

Page: 48 / 240

Setting the DIP Switches

Cha

he DIP sw

ch se

tting

he follow

ing

cases.

• Whe

ach

ing

he power sw

ch cover

o preve

he power sw

ch from be

ing

pressed

• Whe

cha

nging

he LCD d

splay la

ngu

• Whe

cha

nging

he vol

me of

he b

zzer

Setting Procedure

he s

eps below

o cha

he DIP sw

ch se

tting

Make sure the power supply for the printer is turned OFF.

Open the ink cartridge cover and remove the DIP switch cover.

Set the DIP switches, using the tip of a tool, such as a small screwdriver.

Attach the DIP switch cover, and close the ink cartridge cover.

CAUTION

Turn the power off before removing the DIP switch cover.



Otherwise, a short-circuit may cause the printer to malfunction.

DIP switch setting becomes enabled after turning the power on or completing reset by the
interface.

Summary of Contents for TM-C3500 Series

















































































































































































































































Search results

Summary of Contents for TM-C3500 Series

Reviews:

Related manuals for TM-C3500 Series

Brands by name

Popular brands

Epson TM-C3500 Series, Technical Reference Manual

Search results

Summary of Contents for TM-C3500 Series

Reviews:

Related manuals for TM-C3500 Series

Brands by name

Popular brands