Epson SureColor SC-F9330 Series User Manual Download Page 13

Page: 13 / 145

Pressing this button displays the Media Setup menu
on the screen to perform

Feed To Cut Position

Media Remaining

Select Media

Customize

Settings

, and

Easy Media Setup

“The Media Setup Menu” on page 94

If you press this while printing, you can adjust the
media feed.

“Correcting Banding” on page 51

Display

Displays the printer's status, menus, error messages,
and so on.

“Understanding the Display” on

page 14

Menu button

Press this button to display menus.

“Using the

Control Panel Menu” on page 88

button (back button)

Press this button to exit to the previous menu when
options are displayed.

“Menu Operations” on

page 88

buttons (left and right arrow buttons)

Use to position the cursor when performing such
tasks as entering a

Setting Name

IP address

in the

setup menu.

buttons (up and down buttons)

❏

When the media loading lever is in a lowered position
and the

button is pressed, media is fed. If the

button is pressed, media is rewound. This occurs
regardless of the way the loaded media is rolled.
Note that when the

button is used to rewind, the

media will stop when its edge reaches the starting
print position. Rewind can be resumed by releasing
the button and then pressing it again.

❏

When the media loading lever in a raised position, the
button to rewind media depends on how the loaded
media is rolled.
Printable Side Out: Press the

button.

Printable Side In: Press the

button.

Keep the button pressed to rewind the media up to
25 cm.

❏

When the menus are displayed, these buttons can be
used to select menu items and options.

“Menu

Operations” on page 88

button

❏

Pressing this button when a menu item is highlighted
displays options for the selected item.

❏

Pressing this button when an option is highlighted
selects the highlighted item or performs the selected
operation.

❏

Pressing this button while the alert buzzer is sounding
stops the buzzer.

button (heating/drying button)

The Heating & Drying menu appears, and you can
do

Start Preheat

Heater Temperature

Blank Area

Feed

Drying Time Per Pass

, and

After Heater

Feed

. You can only set

Heater Temperature

while

printing.

“Changing the Heater's Temperature” on

page 50

button (maintenance button)

The Maintenance menu appears, and you can do

Nozzle Check

Cleaning

Head Maintenance

Replace Ink Bottle

Head Cleaning Set

, and

Other

Maintenance

. Operations do not occur while

printing, no matter which button is pressed.

“The Maintenance Menu” on page 104

button (pause/cancel button)

❏

The printer enters pause status if this is pressed while
printing. To release the pause status, press the

button again, or select

Pause Cancel

on the screen

and then press the

button. To cancel print jobs

being processed, select

Job Cancel

on the screen and

then press the

button.

❏

Pressing this button when menus are displayed closes
the menus and returns the printer to ready status.

[

] button (light button)

Press when the internal light is on to turn off the
light.

Press when the internal light is off to turn on the
light.

However, when you press the button during an
operation that does not allow the light to turn on, the
light remains off.

SC-F9300 Series User's Guide

Introduction

Summary of Contents for SureColor SC-F9330 Series


















































































































































Search results

Summary of Contents for SureColor SC-F9330 Series

Reviews:

Related manuals for SureColor SC-F9330 Series

Brands by name

Popular brands

Epson SureColor SC-F9330 Series, User Manual

Search results

Summary of Contents for SureColor SC-F9330 Series

Reviews:

Related manuals for SureColor SC-F9330 Series

Brands by name

Popular brands