Epson SureColor SC-F9330 Series User Manual Download Page 75

Page: 75 / 145

Lower the stopper.

Important:

Seal the mouth of the bottle with the stopper. If
there is a gap, waste ink may splatter and stain
the surrounding area.

Press the

button.

Check again to confirm that a new Waste Ink
Bottle has been installed correctly. Press the

button to clear the waste ink counter.

Leave the waste ink in the Waste Ink Bottle for disposal;
do not transfer it to another container.

Note:

Note the following points when transferring waste ink
from the waste ink bottle to another container.

❏

Use a container made of PE (polyethylene) when
transferring the waste ink.

❏

Attach the spout included with the printer to the rim
of the waste ink bottle and transfer the waste ink.

❏

Pour the waste ink carefully. Pouring the waste ink
quickly may cause it to spill and splatter.

❏

Store the waste ink by securely closing the lid of the
container to which you transferred it.

Disposing of used waste ink and Waste Ink Bottle

“Disposal” on page 80

Replacing the Head
Cleaning Set

Preparing and Replacement
Timing

When Head cleaning set is nearing end of life. is
displayed

Prepare a new head cleaning set as soon as possible.

When you want to replace the parts at this stage due to
night operations and so on, implement

Head Cleaning

Set

from the setup menu, and then replace the parts. If

you replace them without implementing

Head

Cleaning Set

, the head cleaning set counter will not

operate correctly.

Maintenance menu

“The Maintenance Menu” on

page 104

Important:

About the Head Cleaning Set Counter

The printer tracks amounts consumed using the
head cleaning set counter and displays a message
when the counter reaches the warning level.

If you replace parts when the message “

Head

Cleaning Set Life

” is displayed, the counter is

cleared automatically.

If you need to replace the parts before the message is
displayed, implement

Head Cleaning Set

from the

setup menu.

Maintenance menu

“The Maintenance Menu”

on page 104

When

Head Cleaning Set Life is displayed

See the following page, and replace all the parts included
in the head cleaning set. Printing cannot be performed if
the parts are not replaced.

The head cleaning sets contains the following parts.

❏

Wiper unit (x1)

❏

Flushing pad (x1)

SC-F9300 Series User's Guide

Maintenance

Summary of Contents for SureColor SC-F9330 Series


















































































































































Search results

Summary of Contents for SureColor SC-F9330 Series

Reviews:

Related manuals for SureColor SC-F9330 Series

Brands by name

Popular brands

Epson SureColor SC-F9330 Series, User Manual

Search results

Summary of Contents for SureColor SC-F9330 Series

Reviews:

Related manuals for SureColor SC-F9330 Series

Brands by name

Popular brands