manualshive.com logo in svg

Epson SureColor SC-F9330 Series, User Manual

Share
Download
Epson SureColor SC-F9330 Series User Manual Download Page 108

Messages

What to do

Auto Take-up Reel Unit stopped.

Media is not correctly attached to the Auto Take-up Reel Unit.

Press the 

W

 button and select 

Job Cancel

 to cancel printing.

Flip the Auto switch on the Auto Take-up Reel Unit to the Off position, then flip it
back and reattach the media to the Auto Take-up Reel Unit.

U

 

“Take-up with the Printed Side Facing Out” on page 39

U

 

“Take-up with the Printed Side Facing In” on page 37

Internal Temp. High
Lower room temperature.

Lower the temperature of the room until it is within the temperature range
described in the “Specifications Table”.

U

 

“Specifications Table” on page 131

Internal Temp. High
Turn printer off. Wait for printer to cool and
then turn on again.

Turn off the printer's power, and lower the temperature of the room until it is
within the temperature range described in the “Specifications Table”.

When the temperature of the room has fallen, turn on the printer's power.

The same error will occur, even with the power on, if the temperature has not
completely fallen.

U

 

“Specifications Table” on page 131

Media Size Error
Load correct size media.

The media currently loaded is not the correct width. Raise the media loading lever
and remove the media.

The narrowest width supported by the printer is 300 mm. Be sure the media is at
least 300 mm wide.

If this message is displayed even though the media is the correct width, the printer
may print if 

Off

 is selected for 

Media Size Check

.

U

 

“The Printer Setup Menu” on page 99

Media Sensor Error
Loaded media or sensor has a problem.
Refer to manual for error details.

Media Sensor Error
Refer to manual for details of error.
Adjust manually?

Press the 

W

 button to clear the message from the display.

Auto Feed Adjustment in 

Media Adjust

 and Auto Feed Adjustment in Easy Media

Setup cannot be executed with the following media, settings, or environments.

❏

Media with an uneven surface

❏

Media that bleeds-through easily

❏

Platen Gap

 is set to 

2.5

 in the media settings.

❏

The printer is used in a place that is exposed to direct sunlight or interference
from other ambient light sources.

In these cases, execute the manual menu.

U

 

“Media Adjust” on page 48

If the printer is exposed to interference from ambient light sources, shade the
printer from these sources and perform the function again; it may succeed. When
the function has failed after shading the printer, execute the manual menu.

If the above does not apply when you are executing Auto Feed Adjustment for
Easy Media Setup and Media Adjust, refer to the online manual, Troubleshooting &
Tips.

Roll Type Error
Release and then reset the media loading
lever, then match Roll Type setting to
actual media.

❏

Does the 

Roll Type

 specified at media loading match the actual roll type?

Raise the media loading lever to resolve the error. Lower the media loading
lever again, and follow the on-screen instructions of the printer to correctly
specify the 

Roll Type

.

SC-F9300 Series     User's Guide

Problem Solver

 

108

Summary of Contents for SureColor SC-F9330 Series


















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands