manualshive.com logo in svg

Epson SureColor SC-F9330 Series, User Manual

Share
Download
Epson SureColor SC-F9330 Series User Manual Download Page 65

If no other parts need to be cleaned, proceed to the
following section.

U

 

“Finishing Cleaning” on page 65

Finishing Cleaning

After cleaning is complete, close the right-side
maintenance cover and press the 

Z

 button.

The menus will close when the print head returns to its
normal position.

To continuously make prints, perform Nozzle Check.

U

 

“Printing nozzle check patterns” on page 81

Disposing of used ink cleaner, cleaning sticks, and
clean-room wipers 

U

 

“Disposal of used consumables”

on page 80

Ink refill

Time Period for Ink Refills

Immediately take care of the following two points when

Check Ink Levels

 message is displayed on the control

panel screen.

❏

Prepare an ink pack of the appropriate color.

❏

Check the level of the ink. If the remaining ink is 70
mm or less from the bottom of the ink tank, replace
the chip unit and refill the ink.

Printing cannot be done if even one color is 

Charge

Expended

 or 

Refill Ink Tank

. If the 

Check Ink Levels

message is displayed during a print job, you can replace
the chip unit and refill the ink while printing continues.

Ink Packs Compatible with this Printer

U

 

“Options

and Consumable Products” on page 116

c

Important:

This printer has a remaining ink warning system.
Information about the available amount of ink in
one pack is recorded in the chip unit supplied with a
new ink pack. This information is written to the
printer when the chip unit is mounted on the
printer.

The ink remaining warning system estimates the
remaining ink based on the ink usage conditions
and the information written to the printer about the
available amount of ink in one pack, and then
displays a message.

To maintain the accuracy of this system, replace the
chip unit and refill the ink as soon as possible once
the remaining ink is 70 mm or less from the bottom
of the ink tank.

Writing the information about available amount of ink
in one ink pack when a chip unit is installed on the
printer is called “charging”.

After charging, the chip unit that was mounted on the
printer is no longer needed. If you replace it with the
chip unit attached to a new ink pack, charging will be
done automatically when required.

Installing a new chip unit on the printer to do automatic
charging is called “Reserving”.

Reserving can be done at any time if the indicator's level
for the estimated amount of ink is between 1 and 6.

However, when reservation is done, a warning is not
displayed when the estimated amount of ink becomes
low. Refill the ink with one pack of ink if the remaining
ink is 70 mm or less from the bottom of the ink tank.

SC-F9300 Series     User's Guide

Maintenance

 

65

Summary of Contents for SureColor SC-F9330 Series


















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands