Epson SureColor SC-F9330 Series User Manual Download Page 40

Page: 40 / 145

Flip the Auto switch to Off and hold down the
Manual switch on the

side to take-up the

media for a single wrap around the core.

Flip the Auto switch to

Confirm that the media is attached without
looseness.

If the tension on the left and right of the media is
different in the areas shown in the illustration
below, the media will not be taken up correctly.
When one side is loose, restart the procedure
from Step 1.

Note:

You can confirm differences in tension by lightly
tapping both edges of the media as shown in the
illustration below.

SC-F9300 Series User's Guide

Basic Operations

Summary of Contents for SureColor SC-F9330 Series


















































































































































Search results

Summary of Contents for SureColor SC-F9330 Series

Reviews:

Related manuals for SureColor SC-F9330 Series

Brands by name

Popular brands

Epson SureColor SC-F9330 Series, User Manual

Search results

Summary of Contents for SureColor SC-F9330 Series

Reviews:

Related manuals for SureColor SC-F9330 Series

Brands by name

Popular brands