manualshive.com logo in svg

Epson SureColor SC-F9330 Series, User Manual

Share
Download
Epson SureColor SC-F9330 Series User Manual Download Page 52

Printable area

The left and right edges of media recognized by the printer varies as shown below according to the Media Size
Check settings.

Media Size Check 

On

: The printer automatically detects the left and right edges of the loaded media.

When media edge plates are attached, within 5 mm of the left and right edges of the media is
recognized as the media edge.

The edges of the media are not detected correctly if the media edge plates are not attached
correctly.

U

 

“Loading media” on page 27

Media Size Check 

Off

: The center of the black rectangle on the heater's label (shown in the illustration below) is the

standard position for the right edge of the media. Regardless of the width of the loaded
media, the left edge of the media is determined to be 1,626 mm (64 inches) from the standard
position for the right edge.

SC-F9300 Series     User's Guide

Basic Operations

 

52

Summary of Contents for SureColor SC-F9330 Series


















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands