manualshive.com logo in svg

Epson EpsonNet C82391, Administrator'S Manual

Share
Download
Epson EpsonNet C82391 Administrator'S Manual Download Page 29

2

Easy Setup Configuration      

2-1

Chapter 2

Easy Setup Configuration

You can use EpsonNet WinAssist Easy Setup to configure the 
printer for use on a network using either the TCP/IP protocol or 
the NetBEUI protocol.

If EpsonNet WinAssist is installed on your computer, you can 
access EpsonNet WinAssist Easy Setup from the Start menu. If 
EpsonNet WinAssist is not installed on your computer, you can 
access EpsonNet WinAssist Easy Setup directly from the CD-
ROM. Refer to the appropriate section below.

Note:

Make sure that the TCP/IP protocol is installed in your computer. To 
print using NetBEUI, make sure that the NetBEUI protocol is installed 
on your computer. See Appendix A, “Installing Protocols,” to install 
the necessary protocols.

Summary of Contents for EpsonNet C82391












































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands