manualshive.com logo in svg

Epson EpsonNet C82391, Administrator'S Manual, Page: 244 / 299

Share
Download
Epson EpsonNet C82391 Administrator'S Manual Download Page 244

13-2      

EpsonNet Internet Print Utility

Environment

Operating systems

❏

Windows 98, Windows 95, or Windows NT 4.0 Server and 
Workstation

❏

An Intel x86 series or compatible processor

Supported products

❏

EPSON print servers that support IPP (EpsonNet Internet 
Print comes with interface cards, printers, and network 
adapters that support IPP)

Installing EpsonNet Internet Print

Follow the steps below to install EpsonNet Internet Print.

1. Be sure that the TCP/IP protocol is installed in the computer 

and a valid IP address is set for the computer and printer.

2. Insert the Software CD-ROM included in the package in the 

CD-ROM drive.

3. The EPSON Installation Program screen opens automatically.

If the EPSON Installation Program screen does not appear 
automatically, click 

Start

 and 

Run

. Type 

D:\EPSETUP

 and 

click 

OK

. (Substitute the appropriate letter for your CD-ROM 

drive as necessary.)

4. Double-click 

Install EpsonNet Internet Print

; or install by 

selecting 

Install EpsonNet Internet Print 

and then clicking the 

arrow at the top right.

5. Follow the on-screen instructions to complete the installation.

6. Restart the computer after installation is complete.

Summary of Contents for EpsonNet C82391












































































































































































































































































































Reviews:

No comments