Epson EpsonNet C82391 Page 248 Administrator'S Manual Download

Page: 248 / 299

13-6

EpsonNet Internet Print Utility

5. Click

to save settings.

6. When a message appears saying the settings are correctly

configured, click

to start the Add Printer Wizard. Click

Note:

If you click Cancel and then later want to add the printer, start the
Add Printer Wizard and follow the steps below.

7. Click the

Local printer

radio button and click

8. Select the printer driver and click

If the following dialog box appears, select

Replace existing

driver

and click

Summary of Contents for EpsonNet C82391












































































































































































































































































































Search results

Summary of Contents for EpsonNet C82391

Reviews:

Related manuals for EpsonNet C82391

Brands by name

Popular brands

Epson EpsonNet C82391, Administrator'S Manual

Search results

Summary of Contents for EpsonNet C82391

Reviews:

Related manuals for EpsonNet C82391

Brands by name

Popular brands