Epson EpsonNet C82391 Page 201 Administrator'S Manual Download

Page: 201 / 299

EpsonNet Direct Print Utility

11-7

4. Double-click the

Epson_lpr

icon to view available printers.

5. Double-click the target printer.

6. Follow the on-screen instructions that the Add Printer wizard

gives you. If you are required to install the printer driver,
follow the instructions in the user’s guide that came with the
printer.

Note:

If the Add Printer wizard asks you to select either

Keep existing

driver

Replace existing driver

, be sure to select the

Replace

existing driver

radio button.

Summary of Contents for EpsonNet C82391












































































































































































































































































































Search results

Summary of Contents for EpsonNet C82391

Reviews:

Related manuals for EpsonNet C82391

Brands by name

Popular brands

Epson EpsonNet C82391, Administrator'S Manual

Search results

Summary of Contents for EpsonNet C82391

Reviews:

Related manuals for EpsonNet C82391

Brands by name

Popular brands