Epson EpsonNet C82391 Page 119 Administrator'S Manual Download

Page: 119 / 299

Settings for Windows 2000/NT

6-7

6. In the Print Destinations dialog box, select

LPR Port

from the

Available Print Monitors list and click

7. In the Add LPR Compatible Printer dialog box, enter the IP

address of the interface card and the name of the printer, and
click

8. If the Print to box shows “IP address: printer name” in the

Create Printer dialog box, the setting is complete.

Note:

Since your clients need to know the share name of the printer in order
to use it, you need to announce the share name to your clients.

Summary of Contents for EpsonNet C82391












































































































































































































































































































Search results

Summary of Contents for EpsonNet C82391

Reviews:

Related manuals for EpsonNet C82391

Brands by name

Popular brands

Epson EpsonNet C82391, Administrator'S Manual

Search results

Summary of Contents for EpsonNet C82391

Reviews:

Related manuals for EpsonNet C82391

Brands by name

Popular brands