EPSON LX-300+II/300+II RTP/1170II
Revision D
PRODUCT DESCRIPTION
Operation
26
1.4.2 Functions
1.4.2.1 Usual Operation
Pause
-This switch alternates printer activity between printing and non-printing.
-Holding it down over 3 seconds when the printer is in the stand-by state, the
Micro Adjust function is enabled. Pressing it again, this function is disabled.
Load/Eject
-Pressing it loads out sheet or continuous paper when the printer is out of paper.
-Pressing it ejects out sheet to the stacker or continuous paper to the paper park.
LF/FF
-Pressing it shortly executes line feed.
-Holding it down for a few seconds executes form feed when continuous paper is
used, or ejects cut sheet to the stacker when cut sheet is used.
Tear Off
-When continuous paper is used, pressing it moves a page to the Tear-off position.
And pressing it again moves a next page to the TOF position.
Font
-Pressing it selects one of the following fonts when Micro Adjust is enabled;
Draft, Draft Condensed, Roman, Roman Condensed, Sans serif, Sans serif
Condensed
Micro Adjust
-Micro Adjust
↓ / ↑
switches is effective when the Micro Adjust function is
enabled by Pause switch.
-Pressing the Micro Adjust
↓ / ↑
switches executes micro feed backward and
forward by 0.118 mm (1/216 inch).
-The TOF adjustment is enabled in the TOF position after loading, and the Tear-
off adjustment is enabled in the Tear-off position.
1.4.2.2 Operation at Power-on
*1 Only for customized models.
*2 LX-300+II only.
Table 1-26. Operation at Power-on
Function
Description of Operation
Self test
Prints the self test pattern. To cancel it, make printer pause and turn off
the power.
Default setting
Starts the default setting mode. See “Default Setting” on page -27.
Data Dump
Starts the data dump mode, in which all the input data are printed as
hexadecimal numbers and corresponding characters.
Clear EEPROM
Resets the printer to the factory default setting, which is not always
proper setting for each market demand.
(i.e. This function is for emergency.)
Clear Area l EEPROM data except 00H to 1FH.
Clear EEPROM for
Driving Line count for
ribbon change timing
Resets the Driving Line count for ribbon change timing.
Color printing position
adjustment *
2
Starts the Color printing position adjustment mode. See “Color
printing position adjustment (LX-300+II Only)” on page -28.
Bi-d adjustment
Starts the Bi-d adjustment mode. See “Bi-d. Adjustment” on page -28.
Copy mode *
1
Starts the copy mode.
Quiet mode *
1
Starts the quiet mode.
Simple default setting *
1
Starts the simple default setting mode.
Error analyzing mode
(acquire EEPROM
information) *
1
Beep once and starts the IEEE1284.4 Protocol mode.
The host system can communicates with Printer in error state.
Program reload mode
for test *
1
Starts the program reload mode, which is reload BOOT area.
(i.e. This function is for emergency.)
Mechanism prohibition
mode *
1
Starts the mechanism prohibition mode, which without initialization of
mechanism.
“Program reload” and “Reply firmware version” are possible without
untying package of printer.
Demonstration
Not available.
Summary of Contents for cLX-300+II RTP
