Epson Buzzer S1C31D51 Technical Manual Download Page 145

Page: 145 / 425

11 SUPPLY VOLTAGE DETECTOR (SVD3)

S1C31D50/D51 TECHNICAL MANUAL

Seiko Epson Corporation

11-7

(Rev. 2.00)

Bits 7–4

SVDRE[3:0]

These bits enable/disable the reset issuance function when a low power supply voltage is detected.

0xa (R/WP):

Enable (Issue reset)

Other than 0xa (R/WP): Disable (Generate interrupt)

For more information on the SVD3 reset issuance function, refer to “SVD3 Reset.”

Bit 3

EXSEL

This bit selects the voltage to be detected when the SVD3CTL.VDSEL bit = 1.

(R/WP): EXSVD1

(R/WP): EXSVD0

Bits 2–1

SVDMD[1:0]

These bits select intermittent operation mode and its detection cycle.

Table 11.6.4 Intermittent Operation Mode Detection Cycle Selection

SVD3CTL.SVDMD[1:0] bits

Operation mode (detection cycle)

0x3

Intermittent operation mode (CLK_SVD3/512)

0x2

Intermittent operation mode (CLK_SVD3/256)

0x1

Intermittent operation mode (CLK_SVD3/128)

0x0

Continuous operation mode

For more information on intermittent and continuous operation modes, refer to “SVD3 Operations.”

Bit 0

MODEN

This bit enables/disables for the SVD3 circuit to operate.

1 (R/WP): Enable (Start detection operations)

0 (R/WP): Disable (Stop detection operations)

After this bit has been altered, wait until the value written is read out from this bit without subsequent
operations being performed.

Notes: • Writing 0 to the SVD3CTL.MODEN bit resets the SVD3 hardware. However, the register val-

ues set and the interrupt flag are not cleared. The SVD3CTL.MODEN bit is actually set to 0

after this processing has finished. If 1 is written to the SVD3CTL.MODEN bit continuously

without waiting for the bit being read as 0 at this time, writing 0 may be ignored and a mal-

function may occur as the hardware restarts without resetting.

• The SVD3 internal circuit is initialized if the SVD3CTL.SVDSC[1:0] bits, SVD3CTL.SVDRE[3:0]

bits, or SVD3CTL.SVDMD[1:0] bits are altered while SVD3 is in operation after 1 is written to

the SVD3CTL.MODEN bit.

SVD3 Status and Interrupt Flag Register

Register name

Bit

Bit name

Initial

Reset

R/W

Remarks

SVD3INTF

15–9 –

0x00

–

SVDDT

–

7–1 –

0x00

–

SVDIF

R/W Cleared by writing 1.

Bits 15–9 Reserved
Bit 8

SVDDT

The power supply voltage detection results can be read out from this bit.

1 (R):

Power supply voltage (V

, EXSVD

) < SVD detection voltage V

SVD

or EXSVD detection voltage V

SVD_EXT

0 (R):

Power supply voltage (V

, EXSVD

)

≥

SVD detection voltage V

SVD

or EXSVD detection voltage V

SVD_EXT

Bits 7–1

Reserved

Summary of Contents for Buzzer S1C31D51










































































































































































































































































































































































































































Search results

Summary of Contents for Buzzer S1C31D51

Reviews:

Related manuals for Buzzer S1C31D51

Brands by name

Popular brands

Epson Buzzer S1C31D51, Technical Manual

Search results

Summary of Contents for Buzzer S1C31D51

Reviews:

Related manuals for Buzzer S1C31D51

Brands by name

Popular brands