manualshive.com logo in svg

Epson AcuLaser M4000 Series, User Manual

Share
Download
Epson AcuLaser M4000 Series User Manual Download Page 202

AcuLaser M4000 Series

User's Guide

Technical Specifications

202

Interfaces

Parallel Interface

Use the IEEE 1284-I compliant parallel interface connector.

ECP mode/Nibble mode

USB interface

USB 2.0 High Speed mode

Note:

❏

Only computers equipped with a USB connector and running Windows XP, XP x64, Me, 98, 2000, 
Server 2003, or Server 2003 x64, support the USB interface.

❏

Your computer must support USB 2.0 in order to use USB 2.0 as the interface to connect your computer 
to the printer.

❏

Since USB 2.0 is fully compatible with USB 1.1, USB 1.1 can be used as an interface.

❏

USB 2.0 can be used with Windows XP, XP x64, 2000, Server 2003, and Server 2003 x64, operating 
systems. If your operating system is Windows Me or 98, use a USB 1.1 interface.

Ethernet interface

You can use an IEEE 802.3 100BASE-TX/10 BASE-T straight-through shielded, twisted-pair 
interface cable with an RJ45 connector.

Summary of Contents for AcuLaser M4000 Series


























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands