Epson AcuLaser M4000 Series User Manual Download Page 118

Page: 118 / 217

AcuLaser M4000 Series

User's Guide

Installing Options

118

Note for Windows users:

If EPSON Status Monitor is not installed, you have to make settings manually in the printer driver. See
“Making Optional Settings” on page 173.

Removing the hard disk drive

Perform the installation procedure in reverse.

Formatting the hard disk drive

1. Make sure the printer is off and all interface cables are disconnected.

2. Hold down the

Down

button while you turn on the printer.

3. When you see the message

Support Mode

on the LCD panel, select

HDD Format

in the support

menu.

Note:

❏

After formatting the Hard Disk Drive, the printer will automatically reboot.

❏

When you want to erase only the fonts installed from the Adobe PostScript 3 (PS3), follow steps 1
through 3 above. Select

PS3 HDD Init

❏

Other fonts installed from PS3 will also be erased.

❏

When installing a Hard Disk Drive from other products, format it with this function.

Interface Card

Your printer comes with a type B interface slot. Various optional interface cards are available to
expand your printer’s interface options.

Installing an interface card

Caution:

Before you install the interface card, be sure to discharge any static electricity by touching a grounded
piece of metal. Otherwise, you may damage static-sensitive components.

Summary of Contents for AcuLaser M4000 Series


























































































































































































































Search results

Summary of Contents for AcuLaser M4000 Series

Reviews:

Brands by name

Popular brands

Epson AcuLaser M4000 Series, User Manual

Search results

Summary of Contents for AcuLaser M4000 Series

Reviews:

Brands by name

Popular brands