Epson AcuLaser C9100 Reference Manual Download Page 51

Page: 51 / 438

Paper Handling

Thick paper and extra thick paper

You can load thick paper (106 to 169 g/m²) or extra thick paper
(170 to 216 g/m²) into the MP tray.

When loading thick or extra thick paper, you should make paper
settings as shown below:

❏

Make settings on the Basic Settings in the printer driver.

❏

You can also make these settings on the Tray Menu in the
control panel. See “Tray Menu” on page 346.

Note:

❏

When using thick and extra thick paper, you cannot do duplex
printing automatically. When you want to make duplex printing
with thick paper, set the

Page side

setting on the control panel’s

Setup Menu to

Back

Front

, then print manually.

❏

When printing on the back side of previously printed paper, select

Thick (Back)

Extra Thick (Back)

❏

When printing on small thick paper, like post cards, select

Thick

Narrow

Paper Size

Paper Source

Paper Type

A4, A5, B5, Letter (LT),
Half-Letter (HLT),
Government Letter
(GLT), Executive (EXE)

MP Tray (up to 18 mm
thick stack)

Thick or
Extra Thick

A3, B4, Ledger (B), Legal

(LGL), Government
Legal (GLG)

MP Tray (up to 10 mm
thick stack)

Summary of Contents for AcuLaser C9100























































































































































































































































































































































































































































Search results

Summary of Contents for AcuLaser C9100

Reviews:

Related manuals for AcuLaser C9100

Brands by name

Popular brands

Epson AcuLaser C9100, Reference Manual

Search results

Summary of Contents for AcuLaser C9100

Reviews:

Related manuals for AcuLaser C9100

Brands by name

Popular brands