manualshive.com logo in svg

Epson AcuLaser C9100, Reference Manual

Share
Download
Epson AcuLaser C9100 Reference Manual Download Page 226

226

Maintenance and Transportation

Toner Cartridge

Handling precautions

Always observe the following handling precautions when 
replacing the consumable products:

❏

Installing a genuine toner cartridge is recommended. Using a 
non-genuine toner cartridge may affect print quality. Epson 
shall not be liable for any damages or problems arising from 
the use of consumable products not manufactured or 
approved by Epson.

❏

When handling toner cartridge, always place them on a clean 
smooth surface.

❏

Do not install used toner cartridge into the printer.

❏

If you have moved a toner cartridge from a cool to a warm 
environment, wait for at least one hour before installing it to 
prevent damage from condensation.

w

Warning:

❏

Do not touch the toner. Keep the toner away from your eyes. 
If toner gets on your skin or clothes, wash it off with soap and 
water immediately.

❏

Keep consumable products out of the reach of children.

❏

Do not dispose of used consumable products in fire, as they 
may explode and cause injury. Dispose of them according to 
local regulations.

❏

If toner is spilled, use a broom and dustpan or a damp cloth 
with soap and water to clean it up. Because the fine particles 
can cause a fire or explosion if they come into contact with a 
spark, do not use a vacuum cleaner.

Summary of Contents for AcuLaser C9100























































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands