manualshive.com logo in svg

Epson AcuLaser C9100, Reference Manual

Share
Download
Epson AcuLaser C9100 Reference Manual Download Page 24

24

Getting to Know Your Printer

1500-sheet Paper Cassette Unit A3 (C12C802152) 

This unit holds three paper cassettes, and increases paper feeding 
capacity up to 1,500 sheets of paper.

Duplex Unit (C12C802132) 

This Duplex Unit allows for automatic printing on both sides of 
the paper.

Face-up Tray (C12C802162)

The face-up tray stacks your printouts with the printed surface 
facing up.

Hard Disk Drive (C12C824172)

This option expands the printer’s capacity by allowing you to 
print complex and large print jobs at high speed. This option also 
enables you to use the Reserve Job function. By using the Reserve 
Job function, you can store print jobs in the printer’s hard disk 
and print them later directly from the printer’s control panel.

Adobe PostScript 3 Kit (C12C832622)

The printer’s Adobe PostScript 3 Mode provides you with the 
ability to print documents formatted for PostScript printers. IES 
(Intelligent Emulation Switch) and SPL (Shared Printer 
Language) support allow the printer to switch between the 
PostScript mode and other emulations as print data is received at 
the printer.

P5C Emulation Kit (C12C832621)

The P5C emulation kit provides you with the ability to print 
documents in the PCL5c printing language with this printer. This 
optional kit includes the ROM module and printer driver.

Summary of Contents for AcuLaser C9100























































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands