manualshive.com logo in svg

Epson AcuLaser C9100, Reference Manual

Share
Download
Epson AcuLaser C9100 Reference Manual Download Page 344

344

Functions of the Control Panel

Status Sheet, AUX Status Sheet, PS3 Status Sheet

Prints a sheet showing the current printer settings and installed 
options. These sheets can be useful to confirm whether options 
have been installed correctly.

Reserve Job List

Prints a list of reserved print jobs stored on the optional Hard Disk 
Drive.

Form Overlay List

Prints a list of the form overlays stored on the optional Hard Disk 
Drive.

Network Status Sheet 

Prints a sheet showing the working status of the network.

Color Regist Sheet

Prints a sheet to check and adjust the registration position of each 
color (Yellow, Cyan, and Magenta). If you notice a misalignment 
of colors, use this sheet to adjust the alignment as explained in 
“Setup Menu” on page 351.

USB ExtI/FStatusSht

PS3 Font List, LJ4 Font Sample, ESCP2 Font Sample, FX Font 
Sample, I239X Font Sample

Prints a sample of the fonts available for your selected printer 
emulation.

Summary of Contents for AcuLaser C9100























































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands