Epson AcuLaser C9100 Reference Manual Download Page 392

Page: 392 / 438

392

Working with Fonts

The following codes are inserted automatically and need not be
input by hand:

❏

Left/Right quiet zone

❏

Start/Stop character

❏

Check digit

❏

Change code set character

Print sample

EPSON ITF

❏

The EPSON ITF fonts conform to the USS Interleaved 2-of-5
standard (American).

❏

Four EPSON ITF fonts are available, allowing you to enable
and disable the automatic insertion of check digits and
OCR-B.

Character type

All ASCII characters (95 in total)

Number of characters

No limit

Font size

26 pt to 104 pt (up to 96 pt in
Windows XP/2000/NT 4.0/Server 2003).
Recommended sizes are 26 pt, 52 pt, 78
pt, and 104 pt.

EPSON Code128

Summary of Contents for AcuLaser C9100























































































































































































































































































































































































































































Search results

Summary of Contents for AcuLaser C9100

Reviews:

Brands by name

Popular brands

Epson AcuLaser C9100, Reference Manual

Search results

Summary of Contents for AcuLaser C9100

Reviews:

Brands by name

Popular brands