Epson 2080 - LQ B/W Dot-matrix Printer User Manual Download Page 64

Page: 64 / 240

2-20

Printing on Continuous Paper

R4C3730
Rev. C

A5 size

Chap2.fm

8/23/99

Pass 0

Proof Sign-off:
<Crestec>

_______

_______

_______

Installing the tractor in the pull position

To install a tractor in the pull position, you must install the
optional pull tractor (C80032

✽

Note:
The tractor in the rear push position cannot be removed.

To install a tractor in the pull position, follow these steps:

1. Make sure the printer is turned off. Lift the printer cover up

and off the printer.

2. Push up the tabs on each side of the paper tension unit and

lift the unit up and off the printer. Store the paper tension unit
in a safe place.

Summary of Contents for 2080 - LQ B/W Dot-matrix Printer

















































































































































































































































Search results

Summary of Contents for 2080 - LQ B/W Dot-matrix Printer

Reviews:

Related manuals for 2080 - LQ B/W Dot-matrix Printer

Brands by name

Popular brands

Epson 2080 - LQ B/W Dot-matrix Printer, User Manual

Search results

Summary of Contents for 2080 - LQ B/W Dot-matrix Printer

Reviews:

Related manuals for 2080 - LQ B/W Dot-matrix Printer

Brands by name

Popular brands