Epson 2080 - LQ B/W Dot-matrix Printer User Manual Download Page 187

Page: 187 / 240

Specifications

C-3

R4C3730
Rev. C

A5 size

APPC.FM

8/23/99

Pass 0

Proof Sign-off:
<Crestec>

_______

_______

_______

Paper capacity:

High-capacity cut-sheet feeder

up to 150 sheets of 82 g/m2 (22 lb) paper
up to 25 plain or bond envelopes
up to 30 airmail envelopes
up to 30 postcards
a stack of multipart forms up to 15 mm
(0.59 in.) thick

Note:
The total thickness of the paper stack can be up to
15 mm (0.59 in.).

Second-bin cut-sheet feeder

up to 50 sheets of 82 g/m

(22 lb) paper

Note:
The total thickness of the paper stack can be up to
5 mm (0.20 in.).

Buffer:

64KB or 0KB (selectable in the
default-setting mode or the EPSON
Remote! utility)

Summary of Contents for 2080 - LQ B/W Dot-matrix Printer

















































































































































































































































Search results

Summary of Contents for 2080 - LQ B/W Dot-matrix Printer

Reviews:

Related manuals for 2080 - LQ B/W Dot-matrix Printer

Brands by name

Popular brands

Epson 2080 - LQ B/W Dot-matrix Printer, User Manual

Search results

Summary of Contents for 2080 - LQ B/W Dot-matrix Printer

Reviews:

Related manuals for 2080 - LQ B/W Dot-matrix Printer

Brands by name

Popular brands