Epson 2080 - LQ B/W Dot-matrix Printer User Manual Download Page 57

Page: 57 / 240

Printing on Continuous Paper

2-13

R4C3730
Rev. C

A5 size

Chap2.fm

8/23/99

Pass 0

Proof Sign-off:
<Crestec>

_______

_______

_______

3. Release the left and right sprockets by pushing the sprocket

lock levers backward.

4. Slide the left sprocket to the left margin of your paper using

the arrow mark inside the printer. (Printing starts at the arrow
mark.) Then pull the lever forward to lock it in place.

Note:
See “Paper alignment” and “Printable area” in Appendix C for
more information on the left margin position.

2-35a.eps

Summary of Contents for 2080 - LQ B/W Dot-matrix Printer

















































































































































































































































Search results

Summary of Contents for 2080 - LQ B/W Dot-matrix Printer

Reviews:

Related manuals for 2080 - LQ B/W Dot-matrix Printer

Brands by name

Popular brands

Epson 2080 - LQ B/W Dot-matrix Printer, User Manual

Search results

Summary of Contents for 2080 - LQ B/W Dot-matrix Printer

Reviews:

Related manuals for 2080 - LQ B/W Dot-matrix Printer

Brands by name

Popular brands