Home
/
epiphan
/
VGADVI Broadcaster Pro
/
User Manual

epiphan VGADVI Broadcaster Pro, User Manual, Page: 157 / 369

Share

Page: 157 / 369

epiphan VGADVI Broadcaster Pro User Manual Download Page 157

VGADVI Recorder Pro User Guide

Connect a source

Connect a source

You can physically connect composite or S-video, SDI, VGA, HDMI or DVI sources to the VGADVI Recorder Pro
at any time, either before or after the system is powered on. Similarly you can disconnect a source from a port
and even connect a different source at any time.

You can also connect wireless RTSP sources to your VGADVI Recorder Pro over a network. Both the RTSP
source device and your VGADVI Recorder Pro need to be powered on to establish a connection. See

for more information.

Changing the source that is being streamed or recorded can result in the recording stopping or the
stream frame size changing depending on how your channel is configured.

If the frame size changes, viewers may be disconnected and need to re-connect to the stream.

Connect sources to the following input ports on your system:

Table 25

Cable and port connections

Source type

Input port

VGA, HDMI* or DVl

DVI port

SDI

SDI port

RTSP

No input port. RTSP sources are connected to your VGADVI
Recorder Pro wirelessly over a network and are configured using the
Admin panel. See

Connect an RTSP source

to learn how to connect

an RTSP source.

composite or S-video source

S-Video port

audio

Audio input port

* VGADVI Recorder Pro only supports video and audio capture from HDMI content that is not HDCP-
protected.

Connect an RTSP source

You can connect RTSP sources such as IP cameras to your VGADVI Recorder Pro over a network using the
Admin panel.

RTSP video encoding is supported with H.264 video codec and MP3 or AAC audio formats.

157

«
...
155
156
157
158
159
...
»

Summary of Contents for VGADVI Broadcaster Pro


















































































































































































































































































































































































Reviews:

No comments