manualshive.com logo in svg

epiphan VGADVI Broadcaster Pro, User Manual, Page: 142 / 369

Share
Download
epiphan VGADVI Broadcaster Pro User Manual Download Page 142

VGADVI Recorder Pro User Guide
                                     

Configure encoding

If desired, you can choose 

Mono

 to have left and right stereo channels combined and 

streamed together (i.e. when listening to the streamed audio, the same blended sound will 
come through both the left and right channels).

 7.  Select an 

Audio bitrate 

from the drop-down menu. The table at the end of this procedure gives some 

guidance on 

audio bitrates

.

For 

stereo 

audio, we recommend 256 kbps or 320 kbps. 

 8.  If all your changes are complete, scroll to the bottom of the page and click 

Apply

.

Table 24 

Audio codecs and bitrate guidance

Value

Description

AAC

AAC is the default audio codec. 

This codec is comparable to MP3, and may have better sound quality with a similar 
bit rate. Supported values are 16, 22, 44 and 48K kHz. Most digital signals (HDMI 
or SDI sources) use 48 kHz audio. 

Matching the encoded level with the source level provides the best sound quality 
by avoiding audio resampling. For analog signals, 44 kHz provides  higher sampling.

The maximum bitrate for mono encoding of a 44 kHz signal is 264 kbps. For stereo, 
320 kbps is supported. Note that lower bitrates (e.g. 32 kbps) with a 44 kHz signal 
may result in distorted audio.

MP3

MP3  provides a common audio format for audio storage. 

Supported values are 22 kHz, 44 kHz and 48 kHz. Most digital signals (HDMI 
or SDI sources) use 48 kHz audio. Matching the encoded level with the source level 
provides the best sound quality by avoiding audio resampling. For analog signals, 
44 kHz provides  higher sampling.

Flash (FLV) doesn't support 48 kHz MP3 audio. When selecting this 
value you'll need to use a media player (or install ASF browser plugins) 
to preview your channel.

PCM

Pulse Code Modulation (PCM) is a standard for digital audio in computer and other 

142

Summary of Contents for VGADVI Broadcaster Pro


















































































































































































































































































































































































Reviews:

No comments