Enterasys Matrix E1 1G582-09 Software Manual Download Page 43 | Manualshive

Page: 43 / 90

background image

STA Information Screen

WebView Local Management Tasks

3-17

The rules defining port status are:

•

A port on a network segment with no other STA compliant bridging
device is always forwarding.

•

If two ports of a switch are connected to the same segment and there
is no other STA device attached to this segment, the port with the
smaller ID forwards packets and the other is blocked.

•

All ports are blocked when the switch is booted, then some of them
change state to listening, to learning, and then to forwarding.

Role

Ports current role in Spanning Tree

Forward
Transitions

See counts of the port’s forward transitions.

Designated Cost

See the path cost from the transmitting port to the root.

Designated Bridge

See the MAC address of the designated bridge to which the port
belongs. This is the switch that is closest to the root switch through
which frames will be forwarded to the root.

Designated Port

See the port designation used by STA for forwarding from this port to
the root.

Table 3-9 STA Information Screen Element Descriptions (Continued)

Use this field…

To…

«
...
41
42
43
44
45
...
»

Summary of Contents for Matrix E1 1G582-09



























































































Reviews:

No comments

Related manuals for Matrix E1 1G582-09

Brand: Fantech Pages: 4

Brand: Harman Kardon Pages: 2

8271 Nways Ethernet LAN Switch

Brand: IBM Pages: 210

Brand: JB Systems Light Pages: 15

Brand: Festo Pages: 2

Brand: GarrettCom Pages: 39

Brand: Fairchild Pages: 20

Brand: Veris Industries Pages: 2

Vertical Horizon VH-2402-L3

Brand: Enterasys Pages: 201

ControlZAPP CZ CEFL 10VDC

Brand: DANLERS Pages: 2

Brand: ClimaxDigital Pages: 9

GSM7352S - ProSafe Switch - Stackable

Brand: NETGEAR Pages: 628

Brand: N-Tron Pages: 2

Brand: Johnson Controls Pages: 4

Brand: Hitachi Pages: 3

Brand: Hitachi Pages: 40

Brand: CYP Pages: 32

Brand: CYP Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands