Enterasys Matrix E1 1G582-09 Software Manual Download Page 14

Page: 14 / 90

Using WebView with Matrix E1 Devices

1-2

Introduction

1.2

USING WEBVIEW WITH MATRIX E1 DEVICES

WebView is an intuitive tool for initial configuration and simple management tasks. It allows a
network manager to perform the following tasks:

•

Assign a new IP address and subnet mask to the device.

•

Select a default gateway.

•

Assign a login password to the device for additional security.

•

Download a new firmware image.

•

Designate which network management workstations receive SNMP traps from the device.

•

View device and RMON statistics.

•

Enable ports to operate in standard or full duplex mode.

•

Configure ports to perform load sharing using trunking commands.

•

Set flow control on a port-by-port basis.

•

Configure ports to prioritize incoming frames.

•

Set 802.1Q VLAN memberships.

•

View and configure basic Spanning Tree device and per-port settings.

Summary of Contents for Matrix E1 1G582-09



























































































Search results

Summary of Contents for Matrix E1 1G582-09

Reviews:

Related manuals for Matrix E1 1G582-09

Brands by name

Popular brands

Enterasys Matrix E1 1G582-09, Software Manual

Search results

Summary of Contents for Matrix E1 1G582-09

Reviews:

Related manuals for Matrix E1 1G582-09

Brands by name

Popular brands