Enterasys Matrix E1 1G582-09 Software Manual Download Page 85

Page: 85 / 90

Port Statistics Screen

WebView Local Management Tasks

3-59

Screen Element Descriptions

Refer to

Table 3-31

for a functional description of each screen element.

Table 3-31 Port Statistics Screen Element Descriptions

Use this field or button…

To…

Port Number

Select the number of the port for which to view statistics.

Etherlike Statistics:

Alignment Errors

For 10 Mbps ports, see counts of alignment errors
(mis-synchronized data packets). For 100 Mbps ports, see counts
of the sum of alignment errors and code errors (frames received
with rxerror signal).

FCS Errors

See the number of frames received that are an integral number of
octets in length but do not pass the FCS check.

Single Collision Frames

See the number of successfully transmitted frames for which
transmission is inhibited by exactly one collision.

Multiple Collision Frames

See a count of successfully transmitted frames for which
transmission is inhibited by more that one collision.

SQE Test Errors

See a count of times that the SQE TEST ERROR message is
generated by the PLS sublayer.

Deferred Transmissions

See a count of frames for which the first transmission attempt on
a particular interface is delayed because the medium was busy.

Late Collisions

See the number of times that a collision is detected later than 512
bit-times into the transmission of a packet.

Excessive Collisions

See the number of frames for which transmission failed due to
excessive collisions.

Internal MAC Transmit
Errors

See the number of frames for which transmission failed due to an
internal MAC sublayer transmit error.

Carrier Sense Errors

See the number of times that the carrier sense condition was lost
or never asserted when attempting to transmit a frame.

Frames Too Long

See the number of frames received that exceed the maximum
permitted frame size.

Summary of Contents for Matrix E1 1G582-09



























































































Search results

Summary of Contents for Matrix E1 1G582-09

Reviews:

Related manuals for Matrix E1 1G582-09

Brands by name

Popular brands

Enterasys Matrix E1 1G582-09, Software Manual

Search results

Summary of Contents for Matrix E1 1G582-09

Reviews:

Related manuals for Matrix E1 1G582-09

Brands by name

Popular brands