Enterasys Matrix E1 1G582-09 Software Manual Download Page 35

Page: 35 / 90

SNMP Community Names Screen

WebView Local Management Tasks

3-9

Screen Element Descriptions

Refer to

Table 3-5

for a functional description of each screen element.

Table 3-5 SNMP Community Names Screen Element Descriptions

Use this field…

To…

Community Name

Enter a community name through which a user will access SNMP
management.

Access Policy

Select the access permission accorded each community name. The
available access levels are:

•

Read-Only

: This community name gives the user read-only access

to the device MIB objects, and excludes access to security-protected
fields of read-write authorization.

•

Read-Write

: This community name gives the user read-write access

to the device MIB objects and also gives “super-user” access
allowing the user to change all modifiable parameters, including
community names, IP addresses, traps and SNMP objects.

Status

Select the status (

Enabled

Disabled

Remove

) for each access

policy.

Summary of Contents for Matrix E1 1G582-09



























































































Search results

Summary of Contents for Matrix E1 1G582-09

Reviews:

Related manuals for Matrix E1 1G582-09

Brands by name

Popular brands

Enterasys Matrix E1 1G582-09, Software Manual

Search results

Summary of Contents for Matrix E1 1G582-09

Reviews:

Related manuals for Matrix E1 1G582-09

Brands by name

Popular brands