Enterasys Matrix E1 1G582-09 Software Manual Download Page 79

Page: 79 / 90

Port Advertised Ability Configuration Screen

WebView Local Management Tasks

3-53

Screen Element Descriptions

Refer to

Table 3-28

for a functional description of each screen element.

Table 3-28 Port Advertised Ability Configuration Screen Element Descriptions

Use this field…

To…

Port

See the port number associated with the displayed status information.

Adv 10M

Set the Port to advertise (or not) 10M Half-Duplex and/or 10M
Full-Duplex.

Adv 100M

Set the Port to advertise (or not) 100M Half-Duplex and/or 100M
Full-Duplex.

Adv 1G

For Ports that support Gigabit Ethernet, set the Port to advertise (or
not) 1G Half-Duplex and/or 1G Full-Duplex.

Adv Flow Ctrl

Set the Port to advertise (or not) Flow Control.

Summary of Contents for Matrix E1 1G582-09



























































































Search results

Summary of Contents for Matrix E1 1G582-09

Reviews:

Related manuals for Matrix E1 1G582-09

Brands by name

Popular brands

Enterasys Matrix E1 1G582-09, Software Manual

Search results

Summary of Contents for Matrix E1 1G582-09

Reviews:

Related manuals for Matrix E1 1G582-09

Brands by name

Popular brands