Enterasys Matrix E1 1G582-09 Software Manual Download Page 75

Page: 75 / 90

Port Information Screen

WebView Local Management Tasks

3-49

Screen Element Descriptions

Refer to

Table 3-26

for a functional description of each screen element.

Table 3-26 Port Information Screen Element Descriptions

Use this field…

To…

Port

See the port number associated with the displayed status information.

Admin Status

See whether the port is administratively

Enabled

(up) or

Disabled

(down).

Link Status

See whether the port has a valid link (

Down

). Link status will be

down until a link is established to an external device and the port is
enabled.

Speed Status

See the port’s operational speed in Mbps (

10M

100M

1000M

Duplex Status

See the port’s duplex mode. Options are:

10M Half-Duplex

10M

Full-Duplex

100M Half-Duplex

100M Full-Duplex

, and

Auto-Negotiation

Flow Control Status

See the port’s flow control status

Enabled

Disabled

, or N/A

(

Auto-Negotiate

is enabled). Flow control is used to manage the

transmission between two devices as specified by IEEE 802.3x to
prevent receiving ports from being overwhelmed by frames from
transmitting devices.

Summary of Contents for Matrix E1 1G582-09



























































































Search results

Summary of Contents for Matrix E1 1G582-09

Reviews:

Related manuals for Matrix E1 1G582-09

Brands by name

Popular brands

Enterasys Matrix E1 1G582-09, Software Manual

Search results

Summary of Contents for Matrix E1 1G582-09

Reviews:

Related manuals for Matrix E1 1G582-09

Brands by name

Popular brands