Enterasys Matrix 7G4202-30 Hardware Installation Manual Download

Page: 93 / 110

Mode Switch Bank Settings and Optional Installations

B-1

Mode Switch Bank Settings

and Optional Installations

This appendix covers the following items:

•

Required tools (

Section B.1

)

•

Locations, functions, and settings for the mode switches (

Section B.2

)

•

Replacing the memory modules (SIMM or DIMM) (

Section B.3

)

B.1

REQUIRED TOOLS

Use the following tools to perform the procedures provided in this appendix:

•

Antistatic wrist strap

•

Phillips screwdriver

Caution:

An antistatic wrist strap is required to perform the procedures in this

appendix. Use the antistatic wrist strap when performing any of the procedures in this
appendix to minimize ESD damage to the devices involved.

Precaución:

Para llevar a cabo los procedimientos especificados en el apéndice

deberá utilizar una pulsera antiestática. Esta pulsera sirve para minimizar los efectos de
las descargas de electricidad estática.

Summary of Contents for Matrix 7G4202-30















































































































Search results

Summary of Contents for Matrix 7G4202-30

Reviews:

Related manuals for Matrix 7G4202-30

Brands by name

Popular brands

Enterasys Matrix 7G4202-30, Hardware Installation Manual

Search results

Summary of Contents for Matrix 7G4202-30

Reviews:

Related manuals for Matrix 7G4202-30

Brands by name

Popular brands