Enotec COMTEC 6000 Assembly, Installation And Operation Manual Download Page 61

Page: 61 / 67

Installation and Operation Manual - COMTEC

6000

Spare Parts

Doc.-ID: COM6000_11022020_EN

Spare Parts

C.1

Mounting Plates of SME-53 Electronic Unit

Mounting Plate 1

Test gas and reference air unit with internal
pumps

TRA-0017

Transformer prim. 2*115V, sec.
115V

PLU-0028

Test air pump for SME5 720 l/h

PGM-0001

Test gas solenoid valve P01 for
SME53 - with pneumatic unit and
fittings

0-P-001508 Restrictor one way - 6 mm

DFM-0001

Internal flow meter for reference
air and test gas SME5

PLU-0025

Reference air pump for SME5
30l/h

Figure 55

- Mounting plate 1 (version with pumps)

Mounting Plate 1

Test gas and reference air unit for instrument

TRA-0017

Transformer primary 2*115V,
sec. 115V

PGM-0001

Test gas solenoid valve P01 for
SME53 - with pneumatic unit and
fittings

PGM-0002

Test gas solenoid valve P02 for
SME5 - with instrument air unit
and fittings

DFM-0001

Internal flow meter

0-P-000752 Pressure

regulator

Figure 56

- Mounting plate 1 (version with instrument

air)

Summary of Contents for COMTEC 6000




































































Search results

Summary of Contents for COMTEC 6000

Reviews:

Enotec COMTEC 6000, Assembly, Installation And Operation Manual, Page: 61 / 67

Search results

Summary of Contents for COMTEC 6000

Reviews: