manualshive.com logo in svg

Enotec COMTEC 6000, Assembly, Installation And Operation Manual, Page: 46 / 67

Share
Download
Enotec COMTEC 6000 Assembly, Installation And Operation Manual Download Page 46

Status Messages

 

Installation and Operation Manual - COMTEC

®

 6000 

46 

Doc.-ID: COM6000_11022020_EN 

6.2 

Alarm Messages 

Error 
Message 

Relay  
contact 

Description 

Reference air 
flow too low 

 

Possible Cause:

 reference air flow set incorrectly, instrument air supply is 

inadequate, reference air pump is faulty. 

Reference air 
flow too high 

 

Possible Cause:

 reference air flow is set incorrectly 

Limit alarm 1 

O

2

 limit 

alarm 1, 
open 

Possible Cause:

 Over or under range of the O

2

 limit alarm. 

Limit alarm 2 

CO

e

  limit 

alarm 2, 
open 

Possible Cause:

 Over or under range of the CO

e

 limit alarm. 

Electronic 
temp. too low 

 

Possible Cause:

 The ambient temperature of the transmitter is lower than  the 

specified lower limit. The specified measurement tolerances are no longer 
guarateed. 

Electronic 
temp. too high 

 

Possible Cause:

 The ambient temperature of the transmitter is higher than  the 

specified upper limit. The specified measurement tolerances are no longer 
guarateed. 

Clock battery 
low 

 

The alarm can only be reset by the user after replacing the clock battery (Lithium 
type 2032). As long as the system is connected to AC power, the alarm has no 
impact. Only after restarting system will the time / date be incorrect. A possible timed 
automatic calibration can no longer work correctly. 

Unlisted alarm messages: Other messages cannot be remedied by the customer. 
Please contact an ENOTEC service point 

6.3 

Service Messages 

Maintenance 
message 

Relay 
contact 

Description 

Measured 
value(s) held 

Service, 
closed 

When the measured values held is set to on, the determined O

2

 mA output remains 

saved for a duration before a calibration. 

 

 

Summary of Contents for COMTEC 6000




































































Reviews:

No comments