Enotec COMTEC 6000 Assembly, Installation And Operation Manual Download Page 10

Page: 10 / 67

Installation

Installation and Operation Manual - COMTEC

6000

Doc.-ID: COM6000_11022020_EN

2.2

Installation of probe signal cable FEP-0007/8

Abide by the maximum cable length (max. 50m)

Note the minimum bending radius.
FEP-0007



Rmin=252 mm

FEP-0008



Rmin=329 mm

Temperature during installa-
tion

Temperature during operation

Cross the probe signal cable

(FEP-0007/8) at right

angle to any power supply cables

COMTEC Probe Cable FEP-0007 (FEP-0008 armored)

No. Function

Diameter

Colors

Info.

Measuring cell

2 x 0,75 mm

white-brown / brown

With shield

Thermocouple 1 2 x 0,75 mm

green / white

With shield

Thermocouple 2 2 x 0,75 mm

green / white

With shield

Probe heater

3 x 1,5 mm

black / blue / green-
yellow

Probe Solenoid
valve

2 x 0,75mm

grey / grey-blue

Sensor

heater and

4 x 1,0mm

red-white / red-white /
red / red

Figure 5

- Probe cable FEP-0007

Caution

Only use ENOTEC probe cables, as the thermocouple cables

and

are compensating cables and

are necessary for correct measurement.
The shield of the probe cable must only be connected at the electronic housing at the PE terminal. Under
no circumstance should the shield also be connected at the probe.

-5 °C

Min.

+50 °C
Max.

-40 °C
Min.

+90 °C
Max.

Summary of Contents for COMTEC 6000




































































Search results

Summary of Contents for COMTEC 6000

Reviews:

Enotec COMTEC 6000, Assembly, Installation And Operation Manual, Page: 10 / 67

Search results

Summary of Contents for COMTEC 6000

Reviews: