manualshive.com logo in svg

Enotec COMTEC 6000, Assembly, Installation And Operation Manual, Page: 15 / 67

Share
Download
Enotec COMTEC 6000 Assembly, Installation And Operation Manual Download Page 15

Installation and Operation Manual  - COMTEC

®

 6000 

Installation

 

Doc.-ID: COM6000_11022020_EN 

15 

2.9 

Adjustment of the Probe Filter Head 

 

Info 

Determine the flow direction of the process gas at the place of installation.

 

 

 

 

Unscrew the retaining ring 

 

 (clock-

wise) with a hook wrench 

 

Turn the filter head V-shield 

 into the 

correct position 

 with a pin wrench. 

The V-shield must face the direction of 
the flue gas 

 . 

 

Tighten the retainer ring 

 after adjust-

ing the filter head.

 

 

 

Figure 9

 - Adjustment of the V-Shield 

 

2.10 

Probe Protection Tube at the Mounting Flange 

 

Info 

Use only new and undamaged gaskets for the installation of the probe. Tighten the nuts firmly, to guaran-
tee the gastight seal of the flange connection. Never leave the probe unheated for longer periods of time 
in the running process.

 

 

 

 

 

Counter flange

 

 

Protection tube

 

 

Protection tube flange 
gasket

 

 

Connection box

 

 

O

2

/CO

e

 probe

 

 

Probe flange gasket

 

 

Probe flange

 

 

 

 

Figure 10

 - Mounting of the protection tube at the mounting flange  

Summary of Contents for COMTEC 6000




































































Reviews:

No comments