manualshive.com logo in svg

Enotec COMTEC 6000, Assembly, Installation And Operation Manual, Page: 42 / 67

Share
Download
Enotec COMTEC 6000 Assembly, Installation And Operation Manual Download Page 42

Service and Maintenance

 

Installation and Operation Manual - COMTEC

®

 6000 

42 

Doc.-ID: COM6000_11022020_EN 

 

 

Prepare the new CO

e

 sensor as follows: 

 

 

Take the clamping ring, the O-ring, retainer 
ring and the cap nut and cover them over 
the CO

e

 sensor.  

 

Note: 

Mind the position of the bevel. 

    Bevel must face O-ring

!

 

Figure 38

 - Prepare the new COe sensor 

 

 

 

Insert the new CO

e

-sensor into the probe 

 

 

Tighten the cap nut. Please tighten the cap 
nut 

once more

 after the system and the 

plant are in normal operation for two hours. 
 

 

Connect the CO

e

 sensor wires at the probe 

terminal block no. 11-14. 
 

 

Switch on the power supply 

Figure 39

 - Insert the new CO

e 

 sensor 

 

 

Caution 

The following parameters have to be entered to ensure correct measurement. Failure to observe this 
information 

will

 

destroy

 

the

 

COe

 

sensor

 

immediately!

 

The CO

e

 sensor must now be activated (via the software)  

SYS-MENU 

 System Configuration 

 Set CO

e

 measurement ON. 

After a CO

e

 sensor replacement, the following values need to be entered as specified in the test  

certificate (

see paragraph 4.2.17

): 

CO

e

 RH

0

 

CO

e

 Offset 

CO

e

 Alpha 

CO

e

 Beta 

CO

e

 Gamma 

CO

e

 Delta 

CO

e

 SO

2

 correction value  

If incorrect values have inadvertently been entered, switch the CO

e

 measurement off and back on 

again. 

 

5.10.1 

Seal the CO

e

 sensor guide tube 

In the event of the CO

e

 sensor being removed for a prolonged period of time, the CO

e

 sensor guide tube must be 

sealed to avoid the intake of false air. This must be done with the 

locking rod

 and 

sealing kit for CO

e

 sensors

 

which are delivered with the probe as accessories.   

2

1

Summary of Contents for COMTEC 6000




































































Reviews:

No comments