manualshive.com logo in svg

Enotec COMTEC 6000, Assembly, Installation And Operation Manual, Page: 39 / 67

Share
Download
Enotec COMTEC 6000 Assembly, Installation And Operation Manual Download Page 39

Installation and Operation Manual  - COMTEC

®

 6000 

Service and Maintenance

 

Doc.-ID: COM6000_11022020_EN 

39 

 

5.8 

Exchange of Probe Inner Part  

Switch off the electronic unit, take the probe out of the protection tube and wait until it has cooled down. 

 

Warning hot surface 

The probe may only be removed with heat-insulated gloves. Before removing the probe, always switch off 
the supply voltage to the electronic system. After removal, store the probe in a safe, protected place and 
wait until it has cooled down below 35 °C/95 °F.

 

Disconnect the wires of the probe inner part 

, the two tubes 

 - 

and the thin reference air tube. Loosen the 

two screws 

 and dismount the plate 

. Now the complete probe inner part (4 hole ceramic rod with measuring 

signal wire, thermocouple and heater) can be unplugged carefully 

. 

Move the new probe inner part carefully into the probe and screw the plate 

. The probe inner part is now pushed 

against the cell by the spring. Connect all electrical and pneumatic connections. Connect the wires as follows

:

 

 

 

Figure 34

 - Probe connection box 

Terminal 

Color 

Description 

Polarity 

Unit 

1 

white/brown 

signal wire, measuring cell 

- 

mV 

2 

orange 

signal wire, measuring cell 

+ 

mV 

3 

green 

thermocouple element 1 

+ 

mV 

4 

white 

thermocouple element 1 

- 

mV 

6 

black 

heating element  

 

 

7 

blue 

heating element  

 

 

8 green/yellow ground/earth 

heater     

9 grey 

solenoid 

valve 

   

10 

grey / blue 

solenoid valve 

 

 

11 

white / red 

CO

e

 sensor measuring value 

 

 

12 

white / red 

CO

e

 sensor measuring value 

 

 

13 red 

(no.3) 

CO

e

 sensor heating element 

 

 

14 red 

(no.4) 

CO

e

 sensor heating element 

 

 

 

 

1

4

2

3

5

6

Summary of Contents for COMTEC 6000




































































Reviews:

No comments