Enerzone Euromax Installation And Operation Manual Download Page 35

Page: 35 / 100

Euromax Pellet Stove Installation and Operation Manual

6.1.10 Filling or Purging Auger Housing

Note: This function is disabled when the stove is running.

To fill or purge the auger housing press the auger icon

and select either “FEED AND

START” or “PURGE SCREW” in the displayed page.

Feed
screw
button

Feed screw
parameters

Feed screw
button when on

Button to stop
the feed screw

6.1.10.1

Feed and Start

Use this option when you start the stove for the first time of the season or after the hopper ran
out of pellets. The auger will turn then the stove will automatically start an ignition cycle.

6.1.10.2

Purge Screw

Use this option to empty the auger at the end of the season. When selected, the auger will
turn for two minutes

STOP

FEED AND START

PURGE SCREW

Summary of Contents for Euromax





































































































Search results

Summary of Contents for Euromax

Reviews:

Related manuals for Euromax

Brands by name

Popular brands

Enerzone Euromax, Installation And Operation Manual

Search results

Summary of Contents for Euromax

Reviews:

Related manuals for Euromax

Brands by name

Popular brands