Enerzone Euromax Installation And Operation Manual Download Page 31

Page: 31 / 100

Euromax Pellet Stove Installation and Operation Manual

6.1.6 Combustion Settings and Pilot Settings depending on Fuel Quality

6.1.6.1 PILOT ADJUSTMENT (Pilot Settings Adjustment)

The “PILOT ADJUSTEMENT” will allow you to modify default settings by ±5% for auger motor
1 and ±10% for combustion and exhaust fan, but will only apply during pilot cycle:

To restore default setting, select “DEFAULT”.

6.1.6.2 COMBUSTION ADJUSTMENT (Fuel Quality Adjustment)

The “COMBUSTION ADJUSTMENT” will allow you to modify default settings by ±5% for
auger motor 1 and ±10% for combustion and exhaust fan.

To restore default setting, select “DEFAULT”.

Here are some situations where you may want to adjust these components:

Summary of Contents for Euromax





































































































Search results

Summary of Contents for Euromax

Reviews:

Related manuals for Euromax

Brands by name

Popular brands

Enerzone Euromax, Installation And Operation Manual

Search results

Summary of Contents for Euromax

Reviews:

Related manuals for Euromax

Brands by name

Popular brands