Enerzone Euromax Installation And Operation Manual Download Page 20 | Manualshive

Page: 20 / 100

background image

20

Euromax Pellet Stove Installation and Operation Manual

4.5.4 Through a Factory Built Chimney

To  make an installation through a factory
built  chimney,  run a 4" stainless steel liner
inside the factory built chimney.

1. Position stove following clearances

given in

Section 3.2 Minimum

Clearances to Combustibles

and

following vent manufacturer’s
instructions.

2. Install a cleanout tee to the stove

exhaust. If necessary, use a horizontal
additional length between the exhaust
and the tee. If you wish to center the
vertical part of the vent with the stove, a
45° elbow and a tee can be used to
route the pipe from the exhaust towards
the back center of the stove.

3. Connect the pellet vent to the stainless

steel liner according to the vent
manufacturer’s instructions.

4. Seal and install vertical roof vent. If

required, seal and install a storm collar.

WARNING: IN THE U.S., THE USE OF A STAINLESS STEEL LINER IS MANDATORY. IN
CANADA, IT IS NOT MANDATORY BUT IS STRONGLY RECOMMENDED.

NOTE: VENTING DIRECTLY IN AN OVERSIZED CHIMNEY AND OMITTING THE USE OF
A STAINLESS STEEL LINER CAN AFFECT CHIMNEY DRAFT AND DECREASE STOVE
PERFORMANCES.

«
...
18
19
20
21
22
...
»

Summary of Contents for Euromax





































































































Reviews:

No comments

Related manuals for Euromax

Brand: NARVI Pages: 4

Brand: Harman Pages: 35

Brand: Harman Pages: 42

Brand: Harman Pages: 36

Advance Freestanding Pellet Stove

Brand: Harman Pages: 44

Advance Pellet Stove

Brand: Harman Pages: 7

Brand: Ravelli Pages: 12

SUPER 27 SPECTRUM

Brand: Pacific energy Pages: 20

Belfort 134 04 11

Brand: FRANCO BELGE Pages: 30

Brand: Clarke Pages: 4

Brand: Clarke Pages: 12

JUNIOR FRANKLIN

Brand: Clarke Pages: 12

Brand: Cola Pages: 14

Brand: Sterno Inferno Pages: 1

Brand: Pelpro Pages: 32

Brand: arilex Pages: 55

Brand: HAAS + SOHN Pages: 31

Brand: High Valley Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands